background image

 

 

 

1  Abbreviations, definitions, symbols and icons 

 

 
Risk of injuri! 

Connect electric circuit points 
only by authorized electrician 
 

 

 

 
Electrostatic strokes!

 

Ground! 

 

 

 
Noise > 85 dB(A)! 

Wear ear protection  

 

 

 
Explosion hazard caused by dust!  

Ground! 

 

 
Explosion hazard! 

Connect only max. admitted 
pressure. 

 

 

 
Risk of injuri! 

Dicharge completely pressure during 
maintenance jobs.  

2  General information 

2.1  Technical documents 

The technical documents are part of the machine and contains important manufacturer information.

 

The 

technical documentation is intended for everyone who uses the cabinet. 

These operating instructions provide important information on handling the device.

 

The precondition for safe 

working is compliance with all specified safety instructions and handling instructions.

 

In addition, the local 

accident prevention regulations applicable to the area in which the device is used and the general safety 

regulations must be followed.

 

Read the operating instructions carefully before starting any work!

 

It is part of 

the product and must be kept in the immediate vicinity of the device and be accessible to staff at all times. 

These technical documents must be made available to all persons who use the blasting cabinet under their 

own responsibility.

 

Those responsible for the plant and operation must ensure that the documentation has 

been read and understood completely. On the basis of this documentation and taking into account the 

industrial safety regulation, appropriate maintenance and test plans as well as operating instructions for the 

operating and maintenance personnel must be derived. 

 

 

NOTE! 

The illustrations in these instructions are for basic understanding and may differ from the 

actual design of the device. 

2.2  Other applicable documents 

The following operating instructions must also be noted: 

Operating instructions single-chamber pressure blasting devices with manual metering valve, pilot 

pressure regulator, TLR outlet valve and water separator 

Operating instructions pressure cyclone 

Operating instructions for the MBX Filter 

Summary of Contents for 100401


































Reviews: