manualshive.com logo in svg

ClearSpan Storage Master Solarguard Building, Assembly Manual, Page: 48 / 51

Share
Download
ClearSpan Storage Master Solarguard Building Assembly Manual Download Page 48

CLEARSPAN

™

 STORAGE MASTER

48

PB02522R6N1D    Revision date: 03.22.19

END W

ALL

 DIAGRAM - FRONT

Ground Level

Front  View

Back  View

Base connection  with baseboard

QH1330  Bracket

11

'

14'

IMPORT

ANT

:

 Pedestrian doors may 

dif

fer

. Measure the door that shipped 

with the shelter

, and frame the door 

opening using those dimensions.

For installation of the  pedestrian door

, 

QH1330

 

brackets are used to  frame the door opening.

NOTE:

 All door dimensions 

are inside-to-inside.

See Jamb Plate Installation 

 

to install the jamb plate.

Frame is shown as seen  from the outside.

 A

TTENTION:

 Use 2" x 2" tubing for the frame around the 14' x 1

1' door only

.

    Pedestrian door can be installed on either side of the overhead door

.

 Use the 

112234B

 self-tapping screws to secure door to end frame.

 Connection views shown are the same for both front and back end walls. 

Summary of Contents for Storage Master Solarguard Building




















































Reviews:

No comments