manualshive.com logo in svg

ClearSpan Storage Master Solarguard Building, Assembly Manual, Page: 16 / 51

Share
Download
ClearSpan Storage Master Solarguard Building Assembly Manual Download Page 16

CLEARSPAN

™

 STORAGE MASTER

16

PB02522R6N1D    Revision date: 03.22.19

13. Tighten the cross-connector and install a Tek screw as 

shown to secure the purlin pipe joint and to secure the 

purlin to the cross-connector.

14. Move to the other upper pipe joint on the inside rafter, 

place a cross-connector over the joint, and repeat 

the steps to install the first two sections of the last 

overhead purlin. 

 

NOTE:

 Position the cross-connector and purlin on the 

rafter pipe joint. Do not remove the temporary bracing 

until additional rafters are in place. 

 

To this point, the assembled frame includes two rafters 

and three top purlins as shown.

FRAME ASSEMBLY (CONTINUED)

15. After attaching the last overhead purlin to the inside 

rafter, move down the rafter assembly to the pipe joint 

below the rafter chord and place a cross-connector 

(#102546) over the rafter pipe. 

This inserts shows the purlin, clamp and cross-

connector as seen from the inside of the building.

16. Insert the first two sections of the pre-marked purlin 

through the cross-connector and into the pipe strap in 

the same position on the end rafter. Tighten the pipe 

strap and secure the purlin to the pipe strap using a Tek 

screw (FA4482).

17. Align the mark on the purlin with the center of the rafter 

leg and tighten the cross-connector. The purlin should 

be saddled in the pipe joint on the rafter.

18. Install a Tek screw (FA4482) through the cross-

connector and through the joint in the purlin to prevent 

separation of the purlin pipe joint.

19. Move to the remaining joint below the rafter chord on 

the inside rafter and attach the first two sections of the 

next purlin. 

The drawing above shows the top 5 purlins in position. 

20. Set the next 

inside rafter assembly

 in position and 

secure it to the feet as previously instructed.

21. Continue to add the cross-connectors and the pre-

marked sections of purlins and secure these to the 

rafter assemblies as previously instructed. 

 

Summary of Contents for Storage Master Solarguard Building




















































Reviews:

No comments