manualshive.com logo in svg

ClearSpan Storage Master Solarguard Building, Assembly Manual, Page: 43 / 51

Share
Download
ClearSpan Storage Master Solarguard Building Assembly Manual Download Page 43

43

CLEARSPAN

™

 STORAGE MASTER

Revision date: 03.22.19    PB02522R6N1D

CONNECTION - DET

AILS 7-10

Cable-Band Clam

p

View 

7

Cable Assembly (Closed-Closed)

View 

9

Cable Assembly (Closed-Open)

View 10

Cable Clamps

Cable Clamps

Note

:  Each cable assembly spans to

 

the corners of the shelter, secure

 

at top of straight side.

AS1003

 Cable Clamp

Open En

d

Cable Clamps

Thimble

Turnbuckle

Thimble

Cable Clamps

Cable Clamps

Thimble

Cable-Over Rafter

View 

8

Mid Length Rafter

Some lengths may not have a  rafter at exact center length, use closest rafter to mid length

.

Open end of  Cable Assembly

Closed En

d

AS1094

 Thimble

Used for closed ends and turnbuckle connections.

104189

 Turnbuckle (Jaw-Jaw)

Cable Clamps

Thimble

Thimble

Cable Clamps

(Seen from the outside)

Band Clamp

Closed End of

 

Cable Assembly

103856

-2.375"

W

rap this cable connection 

with several layers of duct  tape to protect the cover

.

Summary of Contents for Storage Master Solarguard Building




















































Reviews:

No comments