ClearSpan Premium Solar Star Instruction Manual Download | Manualshive

Page: 30 / 45

background image

PREMIUM SOLAR STAR

™

GREENHOUSES

30

Revision date: 11.04.11

SEAL THE POLYCARBONATE PANELS

The following steps describe one way to seal the installed

panels.

NOTE:

The amount of sealant needed to complete

the following steps will vary and depends on how

thick the sealant is applied. Call Customer Service at

1.800.245.9881 to purchase additional sealant if needed.

Open the supplied sealant and apply a thin bead to

1.

the outside of the upper panel to seal the panel to the

U-channel.

Seal the seams between the H-channel and the ends

2.

of the U-channel.
Move to the inside of the greenhouse and run a thin

3.

bead of sealant between the lip of the H-channel and

the polycarbonate panel.

Dashed line identifies the lip

of the H-channel as seen from

inside the greenhouse.

Return to any holes in the H-channel and repair these

4.

using the sealant.

Seal the upper edge of both end walls with a bead of

5.

sealant. See the dashed line in the diagram below.

Frame shown may differ from actual frame.
Read the greenhouse care and maintenance

6.

information that follows.

«
...
28
29
30
31
32
...
»

Summary of Contents for Premium Solar Star














































Reviews:

No comments

Related manuals for Premium Solar Star

Intro Grow DAISY

Brand: ACD Pages: 26

Brand: Greenhouse People Pages: 24

Brand: Mr Fothergill's Pages: 4

GZ 48 - 2,5 x 1,9 m

Brand: G21 Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands