background image

303.872.4477        [email protected]        clearcomfort.com

3

GENERAL INFORMATION

IMPORTANT SAFETY INSTRUCTIONS

1. READ AND FOLLOW ALL 

INSTRUCTIONS. 

2. For cord connected/convertible 

units:

 

DANGER – Risk of injury. 

A. 

Replace damaged cord 

 

    immediately.

B. 

Do not bury cord.

C. 

Connect to a grounding 

 

    type receptacle only. 

3. For all permanently connected 

units intended for use on 15 or 20 

ampere, 125V or 230V, single phase 

branch circuits: 

WARNING – Risk 

of Electric Shock. Connect only to a 

branch 

circuit protected by a ground-fault 

circuit-interrupter (GFCI). Contact a 

qualified electrician if you cannot verify 

that the circuit is protected by a GFCI. 

4. For all cord connected units other 

than storable pool pumps: 

WARNING 

– Risk of Electric Shock. Connect 

only to a grounding type receptacle 

protected by a ground-fault circuit 

interrupter 

(GFCI). Contact a qualified electrician if 

you cannot verify that the receptacle is 

protected by a GFCI. 

5. For all permanently connected 

units: 

WARNING – Risk of Electric 

Shock. Connect only to a branch circuit 

protected by a ground-fault circuit-

interrupter (GFCI). Contact a qualified 

electrician if you cannot verify that the 

receptacle is protected by a GFCI. 

6. For units intended for above-

ground storable swimming pools: 

Do 

not bury cord. Locate cord to minimize 

abuse from lawn mowers, hedge 

trimmers, and other equipment. 

7. For all cord and plug connected 

units: 

WARNING – To reduce the risk 

of electric shock, replace damaged 

cord immediately. 

8. For units intended for above  

ground storable swimming pools: 

WARNING – To reduce the risk of 

electric shock, do not use extension 

cord to connect unit to electric supply; 

provide a properly located outlet. 

9. CAUTION: 

At low or no flow 

conditions, gas may accumulate – 

ensure system is off when backwashing 

or when water is not being treated 

to prevent an unsafe gas buildup. 

Pressure switches, flow switches and 

other safety equipment to prevent 

unsafe gas buildup is recommended.  

10. When the modified air is 

introduced into the pool or spa 

water via the existing plumbing, 

the biocide is produced. Some of the 

remaining activated atoms either keep 

minerals dissolved in the water or 

remove minerals that were previously 

deposited.

11. This unit is to be installed in 

accordance with the installation 

instructions,

 the applicable plumbing 

and building codes, the applicable 

state and local laws and regulations, 

and the requirements of the Authority 

Having Jurisdiction. 

12. When installing and using this 

equipment, 

basic safety precautions 

should always be followed including 

the following. 

13. WARNING -

 To reduce the risk of 

injury, do not permit children to use 

this product unless they are closely 

supervised at all times. 

14. WARNING -

 Do not sit or stand 

on unit.

15. SAVE THESE INSTRUCTIONS.

Summary of Contents for CCW100





























Reviews: