background image

Intended use

DWP - 1106 A | Version 1.03

7

3

Intended use

The DWP 1106 A deep well pump is intended for private 
use in the house and hobby garden. It is intended for 
drawing water from wells and cisterns and for operating 
irrigation equipment. 

The height of the pump is 90 cm. It can therefore be used 
in shallow water depths.

The deep well pump must not be operated in explosive 
environments. 

The maximum permissible temperature of the pumped 
medium must not exceed 35°C. 

Proper use also includes compliance with all the informa-
tion in these instructions.

Claims of any kind for damage due to improper use are 
excluded.

3.1

Improper use

3.2 Residual risks

Even if all safety regulations are observed and the water 
pump is used as prescribed, there are still residual risks, 
which are listed below:

- There is a risk of injury to the upper limbs (e.g. hands, 

fingers).

- Heat development on components can lead to burns 

and other injuries.

- Risk of damage due to absorption of unsuitable liquids.

- Electrical hazard due to contact with parts and high 

voltage (direct contact) or with parts that are under 
high voltage due to a defect in the device (indirect con-
tact). 

4

Type plate 

Fig. 2: Type plate DWP 1106 A

5

Technical Data

WARNING!

Danger in case of misuse!

Misuse of the water pump can lead to dangerous 
situations. 

-  Only operate the deep well pump in the perfor-

mance range specified in the technical data. 

-  Never bypass or disable the safety devices. 

-  Only operate the deep well pump in a technically 

perfect condition.

Model

DWP 1106 A

Length

98 mm

Width / Depth

98 mm

Height

900 mm

Weight

13,59 kg

Supply voltage

230 V

Max. lift

55 m

Discharge capacity

100 l/min

Working pressure

5,5 bar

Discharge port diameter

1“

Max. grain size

1,2 mm

Fluid temperature max.

35°C

Immersion depth max.

18 m

Impeller number

8

Motor type

Asynchron

Rated speed

2800 min¯¹

Motor output

1100 W

Cooling

Water

Running time at 75% 
load

3000 h

Protection class  motor

IPX 8

Connection cable length

22 m

Summary of Contents for 7523105



















Reviews: