Claydon HYBRID M3 Page 30 Operator'S Manual Download | Manualshive

Page: 30 / 66

background image

G

PRE-WORK PREPARATION

30

OPERATORS MANUAL - HYBRID - M3, M4, M4R, M4.8 & M6

Pre-work Preparation

OPENING THE HOPPER

To fill the hopper with seed or fertiliser is by means of removing the hopper cover.

1. Hopper cover

ENSURE HOPPER COVER IS CLOSED WHEN THE MACHINE IS

WORKING

!

!

1.

The hopper cover is

secured by four bungee

cords.

To release the hopper

cover please remove

the two bungee cords

indicated.

Fold the cover in the

direction indicated.

Once finished fold the

cover back and secure

the bungee cords back in

place.

«
...
28
29
30
31
32
...
»

Summary of Contents for HYBRID M3



































































Reviews:

No comments

Related manuals for HYBRID M3

Brand: Rabe Pages: 65

Brand: Yamaha Pages: 78

Brand: Fast Pages: 42

Brand: DARAY Pages: 28

Brand: Backyard Play Systems Pages: 64

Brand: Haenim Pages: 2

Brand: Keithley Pages: 42

Brand: UFO Pages: 16

Brand: Facnor Pages: 33

Brand: ParaBody Pages: 5

Brand: Baileigh Industrial Pages: 28

Brand: Baileigh Industrial Pages: 56

Brand: Kawai Pages: 10

Brand: M-system Pages: 2

Brand: Rico Pages: 34

Brand: unios Pages: 2

Brand: laerdal Pages: 8

Brand: LAHTI PRO Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands