manualshive.com logo in svg

Claydon Hybrid Front Hopper, Operator'S Manual And Part'S Manual, Page: 10 / 54

Share
Download
Claydon Hybrid Front Hopper Operator'S Manual And Part'S Manual Download Page 10

 

Front Hopper  

[8] 

8.2 Connecting the Hopper to the Tractor 

The Claydon Front Hopper is mounted on any CATII or CATIIN compatible three point linkage, 
the linkage pins can be found located on the hopper however the CATII balls are not supplied.   

Connect the main power cable supplied directly to the battery terminals. Ensure the routing of 
the cable can’t be caught or damaged in any way. All connections including the hydraulic 
hoses are displayed in Figure 2. THE HYDRAULIC FREE FLOW SERVICE 

MUST

 BE PLUGGED IN PRIOR 

TO THE HOPPER BEING OPERATED. 

 

Connections 

Colour

 

 

 

1.

 

Hydraulic fan (Pressure) 
 

2.

 

Hydraulic fan (Free flow 
service 18L connector) 

3.

 

Electrical cable 

4.

 

Lights 

5.

 

Power cable  

 

2x Red 

markers 

 

Red 

- 
- 
- 

 

Figure 2 – Front Hopper connections  

 

The following label (Figure 3) can be found located on the rear of the Front Hopper, the label 
specifies the corresponding hydraulic connections and their colour coded indicators. 
 

Hrdyaulic Services

 

 

Hrdraulic fan

 - Red

 

 

Figure 3 – Labels for hydraulic services 

Summary of Contents for Hybrid Front Hopper























































Reviews:

No comments