About the MIDI implementation
The following MIDI messages can be transmitted and received from the
Nord Electro 4 HP/SW:
Note On/Off
• Note On and Note Off messages are transmitted and received .
Controllers
In the MIDI Menu (see page 18) you can select if the Nord Electro 4 HP/
SW should transmit and/or receive Control Change messages .
• If you have a control pedal connected to the control pedal input, this
is transmitted as Controller 11 (Expression) .
• If you have a pedal connected to the sustain pedal input, this is
transmitted as Controller 64 (Sustain Pedal) .
• If you have a pedal connected to the rotor pedal input, this pedal is
transmitted as Controller 90 .
• Almost all other controls (knobs and buttons) on the front panel are
also transmitted (and received) as Control Change messages . This
can be used to record your actions on the front panel into a MIDI
sequencer . For a full list of which parameters correspond to the Con-
troller numbers, see the MIDI Controller list on the next page .
Keyboard velocity
The Nord Electro 4 HP/SW can transmit and receive keyboard velocity
messages . Organ sounds will always be played back at nominal level
regardless of incoming MIDI Velocity data . Release velocity is also
transmitted .
Program change
In the MIDI Menu (see page 18) you can select if the Nord Electro 4 HP/
SW should send and/or receive Program Change messages .
When you select a Program, a Program Change message is transmit-
ted via MIDI . If a Program Change message is received on the selected
MIDI Channel, the Nord Electro 4 HP/SW will change Program accord-
ingly .
The 128 Program locations send and respond to MIDI Program
Change values 0-127 .
MIDI Sysex (System Exclusive)
Individual Programs or all Programs can be transmitted and received as
a System Exclusive dump .
With a sequencer
Connections
1
Connect the MIDI Out on the Nord Electro 4 HP/SW to the MIDI In
on your sequencer .
2
Connect the MIDI Out from your sequencer to the MIDI In on the
Nord Electro 4 HP/SW .
Local On/Off
Local Off may be used when you use a sequencer to record and
play back from Nord Electro 4 HP/SW . If the sequencer echoes back
incoming MIDI data, the Nord Electro 4 HP/SW may respond twice to
every note and other message/action if for example the keyboard and
the sequencer sends the same MIDI information to the unit . Local On/
Off is set on the MIDI menu, see page 18 .
MIDI Channel
The MIDI channel(s) that the Nord Electro 4 HP/SW uses are set up in
the MIDI menu - see the MIDI menu on page 18 . If you use the Organ
model in the split/lower manual configuration, the lower manual can
receive on a separate MIDI channel .
Program Change
Usually you select a Program Change value for a track in the sequenc-
er track settings . The 128 program locations send and respond to
Program Change values 0-127 .
If you want to record a Program Change message, activate recording
in the sequencer and simply select the program on the Nord Electro 4
HP/SW .
Controllers
When you record actions with knobs and buttons, make sure that the
sequencer “echoes” the changes back on the correct MIDI Channel, or
your changes won’t have any effect .
About controllers and “chasing”
Consider a situation where you record a Controller message, e .g . a
Drawbar adjustment, in the middle of your sequencer song . Then you
“rewind” the sequencer to a position before the recorded Drawbar ad-
justment . The problem is that the Nord Electro 4 HP/SW’s Drawbar will
remain as after the adjustment, although it really should be as it was
before you recorded the change .
To solve this, you could record a “snapshot” of all Controller settings of
the Nord Electro 4 HP/SW Program at the beginning of your sequencer
song . See “Sending MIDI Controller dumps” on the next page .
8
MIDI functions
cHaPtEr 8 Midi fUNctioNS
| 21
Summary of Contents for Nord Electro 4 SW
Page 26: ......
