Clarke 6500752 Operation & Maintenance Instructions Manual Download Page 15 | Manualshive

Page: 15 / 28

background image

15

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

CONNECTING THE DUST EXTRACT

This table saw is equipped with a dust
extraction port. For safe operation,
we recommend that a suitable dust
extraction device or vacuum cleaner
is connected during operation.

WARNING: EXCESSIVE SAWDUST BUILD UP AROUND THE MOTOR COULD
POSSIBLY IGNITE AND CAUSE DAMAGE TO THE MOTOR, TABLE SAW OR
YOUR WORKSHOP.

«
...
13
14
15
16
17
...
»

Summary of Contents for 6500752





























Reviews:

No comments

Related manuals for 6500752

Brand: Panasonic Pages: 30

Brand: Gebhardt Anlagentechnik Pages: 152

Brand: Rational Pages: 60

Brand: TANACOM Pages: 27

Brand: iBACheck Pages: 2

Brand: neofeu Pages: 28

Brand: Walimex Pro Pages: 44

Brand: Otto Bock Pages: 72

Brand: Hatco Pages: 24

Brand: LifeSpan Pages: 8

Brand: Vicon Pages: 108

Brand: Emos Pages: 8

Brand: Kärcher Pages: 60

Brand: Croplands Pages: 168

Brand: TaiShan Pages: 5

COVIDAIR S/T EASY

Brand: BCD microtechnique Pages: 21

Brand: Comelit Pages: 8

Brand: Stamina Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands