background image

4

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SAFETY SYMBOLS

The above safety symbols appear on the product.

SAFETY WARNINGS

PERMITTED USAGE

The table saw is constructed exclusively for the sawing of wood. The 
appropriate saw blade should be fitted according to the wood type (solid 
wood, chipboard or plywood).

• Read and understand the entire owner's manual before attempting 

assembly or operation.

• Read and understand the warnings posted on the machine and in 

this manual. Failure to comply with all of these warnings may cause 
serious injury.

HEALTH

When sawing, dust particles will be produced which in some instances can be 
harmful (e.g. lead from old gloss paint, arsenic and chromium from chemically 
treated lumber).

To reduce the risk you should:

Read instruction 
manual before use

Wear dust mask

Wear safety glasses

Wear ear defenders

Indoor Use Only

Danger of cut hand 
injury. Ensure guards are 
in place.

CAUTION: DO NOT LET FAMILIARITY WITH YOUR TABLE SAW MAKE YOU 
CARELESS. REMEMBER THAT A CARELESS FRACTION OF A SECOND IS 
SUFFICIENT TO CAUSE SEVERE INJURY.

Summary of Contents for 6500752





























Reviews: