Clarion VXZ756, Owner'S Manual

Page: 41 / 51

English
280-8177-00
VXZ756
41
Common Operations
Dimmer control
You can set the dimmer control.
∗
The factory default setting is “ ON ”.
1. Press and hold the [ DISP ] button for 1 second
or longer to switch to the display adjust mode.
2. Press the [
a
]/[
d
] button to select
“ DIMMER ”.
3. Turn the [ ROTARY ] knob to select “ ON ” or
“ OFF ”.
4. Press the [ DISP ] button to return to the previ-
ous mode.
Adjusting the display contrast
You can adjust the display contrast to match the
angle of installation of the unit.
∗
The factory default setting is “ 5 ”. (Adjustment level:
1 to 16)
1. Press and hold the [ DISP ] button for 1 second
or longer to switch to the display adjust mode.
2. Press the [
a
]/[
d
] button to select
“ CONTRAST ”.
3. Turn the [ ROTARY ] knob to adjust the con-
trast.
4. Press the [ DISP ] button to return to the previ-
ous mode.
Adjust Mode
Setting the low pass filter
∗
This function can only be adjusted when the
subwoofer output is set to “ ON ” and the speaker
system is set to “ 5.1ch ”. For details on how to set
the subwoofer, refer to the subsection “ Turning
on/off speakers ” in the section “ Changing Initial
Settings such as Menu Language, etc. ”.
∗
This function cannot be adjusted when as follows:
“
Pro Logic ” is set to “ ON ”, the speaker system is
set to “ 5.1ch ”, DVD/DTS-CD is being played.
∗
The factory default setting is “ THROUGH ”. If the
speaker system is set to “ 5.1ch ”, the factory default
setting is “ 50Hz ”.
1. Press the [ ADJ ] button to switch to the adjust
mode.
2. Press the [
a
]/[
d
] button to select
“SUB-W LPF” .
3. Turn the [ ROTARY ] knob to select the setting.
Each time you turn the [ ROTARY ] knob, the
setting changes in the following order:
THROUGH
➜
50Hz
➜
80Hz
➜
120Hz
4. Press the [ ADJ ] button to return to the previ-
ous mode.
Setting the amplifier bypass
circuit
∗
The factory default setting is “ OFF ”.
1. Press the [ ADJ ] button to switch to the adjust
mode.
2. Press the [
a
]/[
d
] button to select “ AMP
CANCEL ”.
3. Turn the [ ROTARY ] knob to select “ ON ” or
“ OFF ”.
●
ON:
Uses with connected AMP.
●
OFF:
Uses with inside AMP.
4. Press the [ ADJ ] button to return to the previ-
ous mode.
Adjusting the auxiliary input
sensitivity
Adjust the auxiliary sensitivity when the audio
from an external device is difficult to hear even
after adjusting the volume.
∗
The factory default setting is “ MID ”.
1. Press the [ ADJ ] button to switch to the adjust
mode.
2. Press the [
a
]/[
d
] button to select
“ AUX SENSE ”.
3. Turn the [ ROTARY ] knob to select from
“ LOW ”, “ MID ” or “ HIGH ”.
4. Press the [ ADJ ] button to return to the previ-
ous mode.
Performing a system check
This function verifies the devices hooked up
through CeNET.
1. Press the [ ADJ ] button to switch to the adjust
mode.
2. Press the [
a
]/[
d
] button to select “ SYSTM
CHK
E E E E E
”.
3. Press and hold the [ ] button for 1 second
or longer to start the system check.
The digital connection configuration is auto-
matically checked.
When the system check is complete, perform
the speaker setting.
Turn the [ ROTARY ] knob to select the
speaker system and press the [ ] button.
The display returns to the previous mode.
For details on the speaker setting, refer to the
“
System check and speaker setting ”.
+VXZ756_01-25-Eng.p65 05.3.1, 6:12 PM 41