Clarion DXZ588RUSB, Owner'S Manual

Page: 15 / 328

Basic Operations
English
15
DXZ588RUSB
●
Q curve
The Q curve becomes sharper when the
numerical value is increased, and smoother
when the numerical value is decreased.
Flat frequency characteristics can be made by
selecting a Q curve opposite to that of the curve
to be compensated.
●
Adjusting the bass
The bass gain, bass FREQ (center frequency)
and bass Q can be adjusted as follows.
The adjustment can only be performed when the
DZE is set to “
DZE OFF ”.
2-1. Select “ BASS ”.
2-2. Press the [ ] button.
2-3. Push the [ SEEK PANEL ] leftward or
rightward and select from:
“ B GAIN ”
↔
“ B FREQ ”
↔
“ B Q ”
3-1. Press the [ UP ] or [ DN ] button to adjust the
gain, the FREQ (center frequency) and the
Q.
B GAIN : –7 to +7 (The factory default
setting is “ 0 ”)
B FREQ : 50Hz/80Hz/120Hz (The factory
default setting is “ 50 ”)
B Q : 1/1.25/1.5/2 (The factory default
setting is “ 1 ”)
3-2. Press the [ ] button to return to the
previous mode.
●
Adjusting the treble
The treble gain and treble FREQ (center
frequency) can be adjusted as follows.
The adjustment can only be performed when the
DZE is set to “
DZE OFF ”.
2-1. Select “ TREBLE ”.
2-2. Press the [ ] button.
2-3. Push the [ SEEK PANEL ] leftward or
rightward and select from:
“
T GAIN ”
↔
“ T FREQ ”
3-1. Press the [ UP ] or [ DN ] button to adjust the
gain and FREQ (center frequency).
T GAIN : –6 to +6 (The factory default
setting is “ 0 ”)
T FREQ : 8KHz/12KHz (The factory default
setting is “ 12K ”)
3-2. Press the [ ] button to return to the
previous mode.
●
Adjusting the sound restorer
The sound restorer enriches the playback of all
types of music files that have undergone any
level of data compression.
∗
The factory default setting is “ OFF ”.
2-1. Select “ S RESTOR ”.
3-1. Press the [ UP ] or [ DN ] button to adjust.
Each time you press the [ UP ] or [ DN ]
button, the sound restorer changes in the
following order:
“ OFF ”
↔
“ 1 ”
↔
“ 2 ”
↔
“ 3 ”
Set this adjustment in accordance with the
music source used.
OFF: For music sources compressed at
high bit rate
1: For music sources compressed for high
quality at low bit rate
2: For music sources compressed for
standard quality at low bit rate
3: For music sources compressed for low
quality at low bit rate
●
Setting high pass filter
2-1. Select “ HPF ”.
3-1. Press the [ UP ] or [ DN ] button to select the
setting. Each time you press the [ UP ] or
[ DN ] button, the setting changes in the
following order:
“ THROUGH ”
↔
“ 50Hz ”
↔
“ 80Hz ”
↔
“ 120Hz ”
∗
The factory default setting is “ THROUGH ”
(through).
●
Setting low pass filter
2-1. Select “ S-W LPF ”.
3-1. Press the [ UP ] or [ DN ] button to select the
setting.
Each time you press the [ UP ] or [ DN ]
button, the setting changes in the following
order:
“ THROUGH ”
↔
“ 50Hz ”
↔
“ 80Hz ”
↔
“ 120Hz ”
∗
The factory default setting is “ THROUGH ”
(through).
Q curve : 20 Q curve : 1
01_DXZ588RUSB_EN.book 15 ページ ２００７年１１月２７日 火曜日 午後６時５分