background image

Page

 

8

  

WS1CS & WS1.25CS Manual

OEM General Instructions

The control valve offers multiple procedures that allow the valve to be modi

fi

 ed to suit the needs of the installation. These 

procedures are:

• 

OEM Softener Setup

• 

OEM Filter Setup

• 

Installer Displays & Settings

• 

User Displays & Settings

• Diagnostics
• Valve 

History

These procedures can be accessed in any order. Details on each of the procedures are provided on the following pages. 

At the discretion of the manufacturer, the 

fi

 eld technician can access all settings. To “lock out” access to diagnostic and valve 

history displays and modi

fi

 cations to settings except hardness, day override, time of regeneration and time of day by anyone but 

the manufacturer, press 

, NEXT, 

, and SET CLOCK in sequence after settings are made. To “unlock”, so other displays can be 

viewed and changes can be made, press 

, NEXT, 

, and SET CLOCK in sequence.

When in operation normal user displays such as time of day, gallons remaining or days remaining before regeneration are shown. 
When stepping through a procedure, if no buttons are pressed within 

fi

 ve minutes the display returns to a normal user display. Any 

changes made prior to the 

fi

 ve minute time out are incorporated. The one exception is current 

fl

 ow rate display under the diagnostic 

procedure. The current 

fl

 ow rate display has a 30 minute time out feature.

To quickly exit OEM Softener Setup, OEM Filter Setup, Installer Display Settings, Diagnostic or Valve History press SET CLOCK. 
Any changes made prior to the exit are incorporated. 

When desired, all information in Diagnostics may be reset to zero when the valve is installed in a new location. To reset to 
zero, press NEXT and

 

 

simultaneously to go to the Service/OEM 1 screen, and release. Press

 

 

and

 

 

simultaneously to 

reset diagnostic values to zero. Screen will return to User Display.

Sometimes it is desirable to have the valve initiate and complete two regenerations within 24 hours and then return to the preset 
regeneration procedure. It is possible to do a double regeneration if the control valve is set to “NORMAL” or “ on 0” in 
Step 8S or Step 7F. To do a double regeneration:

1. Press REGEN once. REGEN TODAY will 

fl

 ash on the display.

2. Press and hold REGEN for three seconds until the valve regeneration initiates.

Once the valve has completed the immediate regeneration, the valve will regenerate one more time at the preset regeneration time. 

Summary of Contents for Water Specialist WS1.25CS





















Reviews: