Claas LEXION 620 Manual Download Page 35 | Manualshive

Page: 35 / 56

background image

Settings:

Cleaning

The fan speed is shown on the
CEBIS screen. The speed range
of the fan is 750rpm – 1600rpm.

With the standard cleaning on the
LEXION 670-620 machines there
are two other adjustments.

•

The wind board

•

The wind throttle

1.Wind board adjustment loosen
nut 3 and adjust. Towards the
rear of the machine more steeper
the angle for the air.

2.To adjust the wind throttle pull
out lock and move lever.

Use these two settings with the
fan speed.

TIP.

Steeper angle for heavier

crops and a lesser angle for
light crops.

TIP.

Open the wind throttle for

heavier crops and shut it for
lighter crops.

Approximately 90% of the grain needs to be separated from the straw by
the time the crop leaves the drum. This means that the remaining 10%
has to be separated by the walkers.

35

TIP.

Only make adjustments of 50rpm at a time.

«
...
33
34
35
36
37
...
»

Summary of Contents for LEXION 620

























































Reviews:

No comments

Related manuals for LEXION 620

Brand: Taber Pages: 27

Brand: KBT Pages: 12

ABS-Lock DH04 Series

Brand: ABS Pages: 4

Brand: Pari Pages: 50

Brand: Icare Pages: 42

Brand: Haas Pages: 12

Brand: SaMASZ Pages: 25

Brand: Balanced Body Pages: 4

Brand: Balanced Body Pages: 2

Reformer Trapeze Combination

Brand: Balanced Body Pages: 164

Brand: Wacker Neuson Pages: 50

Brand: Balanced Body Pages: 37

Brand: MacDon Pages: 238

Brand: Calibre Fitness Pages: 11

Brand: Lumineux Pages: 2

Brand: Xtricity Pages: 4

TR 2B INC INT NC

Brand: OMGA Pages: 76

Brand: Hella Gutmann Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands