Claas LEXION 620 Manual Download Page 45 | Manualshive

Page: 45 / 56

background image

45

EASY:

CRUISE PILOT

To engage CRUISE PILOT press the AUTOPILOT button on the joystick.
The symbols in the HOTKEY direct menu will have the colours inverted on
activation.

To de-activate the CRUISE PILOT either move the control lever with a jerk or
give a short firm press on both foot brake pedals.

To adjust and monitor CRUISE PILOT once in work, turn the HOTKEY to the
CRUISE PILOT symbol.

TIP.

Make sure that the combine has crop going through it before pressing

the AUTOPILOT button on the joystick.

TIP.

If just using CRUISE

CONTROL (fixed ground speed)
drive the combine into the crop
at your desired speed then press
and hold the AUTOPILOT button
for 3 seconds, there will be a
beep from the CEBIS screen. This
speed is now saved.

TIP.

If using Performance mode,

(constant throughput) set the
target throughput to the middle
then increase until you reach your
desired speed.

TIP.

If using the Throughput mode

make sure that the monitors are
showing what you need them to
show.

Check your losses!

«
...
43
44
45
46
47
...
»

Summary of Contents for LEXION 620

























































Reviews:

No comments

Related manuals for LEXION 620

Brand: Oberheim Pages: 40

Brand: Panlux Pages: 2

Brand: Tabi Pages: 8

Brand: Dabi Atlante Pages: 102

Brand: EAW Pages: 2

Brand: abc Pages: 28

Brand: Far Tools Pages: 25

Brand: Xiitech Pages: 6

Brand: Ransomes Pages: 282

Ransomes HR 6010

Brand: Jacobsen Pages: 10

Brand: Jacto Pages: 64

Brand: Parkside Pages: 2

Brand: Park House Healthcare Pages: 12

Brand: Labnet Pages: 12

Brand: Yamaha Pages: 29

Brand: olympia electronics Pages: 2

Brand: stilum Pages: 4

Brand: Anslut Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands