background image

 

 

The City Theatrical PDS-750-TR 

Thank you for using the City Theatrical PDS-750-TR™.   Every effort has been made to 
anticipate your questions in this manual, but if you have any questions that we don’t answer 
here, or you want to discuss a special application, please feel free to contact us directly at City 
Theatrical. 
 
The CTI PDS-750-TR is a portable power supply unit provided with DMX 512 / Color Kinetics® 
data management circuitry.  It is designed to provide 24VDC power and standard DMX512 
distribution connections with DMX field addressing capability for Color Kinetics Fixtures, 
including ColorBlast® 6, ColorBlast 12, and iColor Cove® (other CK fixtures are also supported, 
check with your favorite lighting shop or City Theatrical for details). 

Cautions 

The PDS-750-TR is intended for use only by qualified professionals.  Connection, installation 
and hanging of this equipment must be performed in accordance with all pertinent local, regional 
and national safety codes and regulations.   
 
The PDS-750-TR is intended for indoor use only. 
 
Keep the unit dry!  Do not operate the unit if it gets wet! 
 
Do not operate in excessive heat/direct sunlight. 
 
Be sure installation provides adequate ventilation.  Both the front and the back side of the unit 
must be clear of obstruction and allow free airflow. 
 
There are no user-serviceable parts inside!  Refer to qualified service personnel! 

Compliance Certifications 

ETL Listed, Conforms to UL 508A 
cETL Listed, Certified to Can/CSA Standard 22.2 14-95 

Compatibility with Color Kinetics Equipment 

The CTI PDS-750-TR is produced under license and with the cooperation and approval of Color 
Kinetics Inc. and is the 

only

 such entertainment power supply and control system approved for 

such use.  City Theatrical, Inc. and Color Kinetics, Inc. have made every effort to assure that the 
CTI PDS-750-TR is fully compatible and will operate reliably with Color Kinetics CB and iColor 
Cove fixtures. 

Color Kinetics Fixtures Supported 

The PDS-750-TR will power and control the following Color Kinetics Fixtures: 

  ColorBlast 12:  12 units, 1 per output 

  ColorBlast 6:  24 units, 2 per output 

  ColorBurst 6:  24 units, 2 per output 

  ColorBurst 4:  48 units, 4 per output 

  Colorsplash 2:  24 units, 2 per output 

  iColor Cove:  96 units, 8 per output 

Summary of Contents for Color Kinetics PDS-750-TR













Reviews: