background image

 

 

19 

1.3 min 

20 

1.5 min 

21 

1.6 min 

22 

2 min 

23 

2.3 min 

24 

2.6 min 

25 

3 min 

26 

3.5 min 

27 

4 min 

28 

4.5 min 

29 

5 min 

30 

5.5 min 

31 

6 min 

32 

6.5 min 

33 

7 min 

34 

8 min 

35 

9 min 

36 

10 min 

37 

12 min 

38 

15 min 

39 

20 min 

40 

25 min 

41 

30 min 

42 

40 min 

43 

50 min 

44 

1 hr 

45 

1.5 hr 

46 

2 hr 

 

Color Wash (reverse).Same as above but in counter clockwise rotation (White, 
Yellow, Green, Cyan, Blue, Magenta, & Red). 
 

Cross-Fade. The Cross-Fade effect changes from one preset color to another than 
back again. The DMX 100s switch sets the starting color and the DMX 10s switch 
sets the ending color. The user specified speed is controlled by the DMX 1s switch. 
The following speeds are provided. 

 

5 sec 

10 sec 

30 sec 

1 min 

2 min 

15 min 

30 min 

1 hr 

 

The random color effect produces random colors at user definable speeds. The 
randomly generated color steps from one to the next without and fading. Speed is 
controlled by the DMX 10s and 1s digits. The following speeds are provided: 

 

Summary of Contents for Color Kinetics PDS-750-TR













Reviews: