Citizen IF1-WF01 User Manual Download

Page: 46 / 49

4 WLAN Setup Tool

③

”Help”

Select ”Help” – ”About” to display the version information of the WLAN Setup Tool.

④

”Refresh List” button

Refresh the list of the wireless LAN interface board. The application periodically refreshes the

list, but you can refresh the list manually by clicking this button.

⑤

”Configure using a Web Browser” button

Select the wireless LAN interface board you want to configure, and then click “Configure using

a web browser”. The browser starts and displays the Web manager.

⑥

”Configure the WLAN Board” button

Select the wireless LAN interface board you want to configure, and then click “Configure the

WLAN Board”. See 4-3 Setup Window (page 47).

⑦

Wireless LAN interface board list

The list displays the wireless LAN interface boards connected to the network. The wireless

LAN interface boards connected to the same subnet are displayed.

Summary of Contents for IF1-WF01


















































Search results

Summary of Contents for IF1-WF01

Reviews:

Related manuals for IF1-WF01

Brands by name

Popular brands

Citizen IF1-WF01, User Manual

Search results

Summary of Contents for IF1-WF01

Reviews:

Related manuals for IF1-WF01

Brands by name

Popular brands