Citizen IF1-WF01 Page 14 User Manual Download | Manualshive

Page: 14 / 49

background image

14

2. Preparation

2-1. Connecting the Wireless LAN Interface Board Unit

• Do not pull the Wireless LAN interface board out of the printer and re-insert it. This could

cause malfunctioning.

• To install the Wireless LAN interface board, please contact your Citizen Systems dealer or

service person.

Warning

Connecting to the Printer

1) Switch off the power and remove the power cord from the

printer.

2) If another interface board is installed in the printer, remove

it.

3) Insert the IF1-WF01 into the interface slot of the printer.

4) Connect the interface connector of the IF1-WF01 to the

interface connector inside the printer.

5) Fix the IF1-WF01 in place with screws.

Interface slot

«
...
12
13
14
15
16
...
»

Summary of Contents for IF1-WF01


















































Reviews:

No comments

Related manuals for IF1-WF01

Brand: GE Pages: 4

Brand: ZETR Pages: 2

Brand: dbx Pages: 2

Brand: dbx Pages: 17

HiGain HLU-231 List 8F

Brand: ADC Pages: 7

Brand: Lanner electronics Pages: 59

Brand: red lion Pages: 5

RocketCache 3240X8

Brand: HighPoint Pages: 17

Brand: XtendLan Pages: 52

Brand: ADS Technologies Pages: 21

SRCSASPH16I - RAID Controller

Brand: Intel Pages: 28

Brand: Renesas Pages: 21

Brand: Brickcom Pages: 184

EK-UNI Holder D5 V3

Brand: ekwb Pages: 2

Brand: OWC Pages: 7

Brand: Ublox Pages: 11

BNI EIP-508 05-Z015 Series

Brand: Balluff Pages: 74

Brand: WATT & WELL Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands