Citizen CKG-15K Operating Manual Download Page 14

CKG counting scales user’s guide

 

-    - 

12

SECTION 10 PARAMETERS                   

 
To set the parameters it is necessary to enter a secure menu.  This is done by entering a 
password number when requested. 
 
To enter the parameter menus press the 

TARE

 key during the initial counting of the display 

after power turned on.  The Weight Display will show "PIn" requesting the password 
number to be entered. 
 
The default password is "0000" but other numbers can be set using the parameter menus. 
 
Press the "

O

" key four times.  The display will show "PIn- - - -", Press the 

TARE

 key.   

 
The Parameter menu has 5 functions that can be accessed using the 

Unit Wt

. key   to 

cycle through the  choices.  The Weight Display will show the name of the functions.  To 
enter a function press the 

TARE

 key.  At any time press the 

ZERO

 key to return to 

weighing. 
 

Weight Display    Description 
F1 CAL 

See the calibration section for details 

F2 dI 

Set the scale increment.  Press the 

Unit Wt

. key to cycle through  

the options. Press 

TARE

 to accept the selection. 

F3 Cnt 

Displays the A/D counts.  Press Tare to return to menu. 

F4 Au 

Press the 

Unit Wt

. key to show the options. Select automatic 

accumulation (Au ON) when the scale becomes stable, or Manual 
accumulation (Au OFF), when the user must press the 

M+

 key to 

accumulate data. Also you can set this parameter as P CONT, 
RS-2323 will send data continuously. 

F5 AZN 

Set the auto zero range, Press the 

Unit Wt

. key to cycle through  

the options(0.5d, 1d, 2d, 4d). Press 

TARE

 to accept the selection.

*2

 

F6 PIn 

Set a new password number.  Display will show "P1        " 
Enter the new password number then press the 

TARE

 key. 

Display will change to "P2   ", Enter the password again and press 

TARE 

again. 

The display will show "donE" to show the new password has been 
accepted. 
Record the new password number in a secure place. 

F7 SPD 

Set ADC speed, press U. Wt. Key to select ADC speed, press Tare 
key to enter 
7.5: 7.5 times per second 
15: 15 times per second 
30: 30 times per second 
60: 60 times per second 
Note: 15 times per second or 30 times per second are 
recommendatory 

 

 

 
 
 
 

Summary of Contents for CKG-15K


















Reviews: