background image

During dive 

• 

Do not operate the crown when the watch is wet. 

• 

Be careful not to bump the watch against hard objects when diving 

• 

When the time display system is operation, the alarm for the time 
display system does not sound. This is designed to prevent alarm sound 
misunderstandings while diving. 

• 

In the water, a clear alarm sound may not be heard due to various 
conditions and environments in which the watch is used. When using the 
alarm, pay attention to wet suit and arm position. 

 

After Dive 

• 

Rinse the watch with fresh water to remove salt water and any dirt 
that may have accumulated during the dive. 

• 

Thoroughly wipe and dry the watch after rinsing with fresh water. 

• 

Do not touch the watch with a sharp object to clean or remove foreign 
matter from the sensor. 
If there is foreign matter on the sensor, remove is with fresh water. 
Pay special attention to ensure the sensor is not exposed to any 
chemicals such as alcohol, gasoline, paint thinner, etc. 

 

Notes on Safety 

• 

When the watch’s additional safety function (fail safe operating) 
begins working, immediately stop using the watch and have it checked 
at your closest Authorized Citizen Service Center. 
When the dive meter system functions do not operate properly, or when 
the colon (:) in the digital display flickers on and off (when the 
power cell indicator is in operation), the change-over from the time 
to dive meter system cannot be made. This is because the watch power 
is low which triggered the fail safe operation to action. 
* If you find anything abnormal with the watch operation, other than 
previously described, immediately stop using the watch and have it 
checked by your nearest Authorized Citizen Service Center. 

• 

If the watch is to be used during a dive, be sure to be properly 
trained in dive safety and procedures. This watch cannot be used as a 
primary dive instrument nor substituted for an accompanying diver or 
as a preventative measure against water hazards. 

• 

This watch displays the water depth at up to 80m(260ft) 
When the depth is beyond this, there is no value displayed. 

• 

For safety reasons, we recommend this watch be used in sports diving 
environments up to 40m (133ft) 

 
 

Return to Table of Contents

 

Return to Table of Contents

 

Summary of Contents for C020
















Reviews: