background image

25 

Warranty 

- The usual Warranty period granted on our devices cover 12 
months after the delivery – the date of Invoice being decisive. 
- Any cases of consequential damage due to the failure of the 
hot air generators and boilers during operation 
will be excluded. 
 
WARRANTY IS VOID IF: 
-     Burner is not maintained in accordance with maintenance 
requirements. 

-

Wiring is not in accordance with circuit diagram 

-

EL fuel oil according to the DIN Standard No.51 603-1 is 
used at temperature below +4 C or if winter diesel is used 
below stipulated temperatures. (IT IS STRICTLY PROHIBITED 
TO ADD ANY PETROL!!!). The Burners must not be modified 
or tampered with under circumstances, and repair work 
must be carried out by a specialist. 

-

Without the proof of a technically correct delivery, any 
warranties from the side of the Company CITERM will 
lapse. 

-

If the pump pressure is set at a higher value, the motor will 
be overheated and may be damaged, excluding any 
warranties. 

-

The Warranty will only be granted if a regular servicing is 
carried out at least once a year in accordance with the 
CITERM operating instructions.  

Summary of Contents for G1p


























Reviews: