citEcar Bubble Buddy Owner'S Manual Download Page 17

17 

 

WARNING!

  Before  you  use  the  charger,  please  read  the  operation  manual  provided  with  the 

charger. 

 

WARNING! 

Explosive  hydrogen  gas  is  produced while  the  battery  is  being  charged.  Only  charge 

the battery in well-ventilated areas. 

 

WARNING! 

Before using the charger, please check to make sure the battery charger you are going 

to use is correctly rated as per your local AC electricity network.   

 

WARNING! 

When using a new battery, make sure the new battery is in same specifications as the 

original one and is appropriate in application.   

 

The following are the charging steps: 

1)  Turn the ignition/power key to OFF. 

2)  Connect the DC output plug to the vehicle receptacle; and then connect it to your local AC power outlet. 

WARNING!   

Do not disconnect the DC output cord from the battery receptacle when the charger is ON.   

Otherwise an arc could occur which may cause an explosion.   

3)  The charger will turn off automatically when the battery is charged fully. 

WARNING!   

For non-onboard charger, the battery receptacle is combined with a security switch which can cut 

off the power of the vehicle when the battery is being charged, so the vehicle cannot be started as 

long as the DC plug is plugged into the battery receptacle. For onboard charger, the vehicle can be 

driven  when  the  charger  is  connected!  Do  not  try  to  drive  the  vehicle  when  the  charger  is 

connected to avoid any possible damage to the charger or vehicle.   

4)  After the charger turns off, disconnect the plug on the AC charging cable from the AC power outlet first, 

and then disconnect the DC output plug from the vehicle receptacle. 

5)  It is prohibited to open the housing of the charger.   

6)  Only a qualified electrician is allowed to open the housing of the charger. 

7)  The charger should be stored in a safe and dry room with good ventilation. 

8)  The charger should be packed properly if not used for long time. 

9)  Read carefully the operation manual for the charger for detailed operation instructions. 

 

Equalizing charge

   

Equalizing is an overcharge performed on flooded lead acid batteries after they have been fully charged. It 

reverses the buildup of negative chemical effects like stratification, a condition where acid concentration is 

greater at the bottom of the battery than at the top. Equalizing also helps to remove sulfate crystals that 

might  have  built  up  on  the  plates.  If  left  unchecked,  which  is  called  Sulfation,  it  will  reduce  the  overall 

capacity of the battery.

   

 

When the battery is fully charged, and it stays connected with the charger, every 8 hours the charger will 

charge  8  minutes  to  maintain  the  battery.  After  20  hours,  equalizing  charge  will  start  and  last  2  hours. 

Equalizing charge can also be started manually by pressing down the ‘STOP’ button for 5 seconds when 

charging. Equalizing charge will start in 1 hour when the battery is fully charged. 

 

Equalizing  is  recommended  when  low  or  wide  ranging  specific  gravity  (+/-  .015)  is  detected  after  fully 

charging a battery. 

 

Summary of Contents for Bubble Buddy































Reviews: