Cisco PA-5EFL= Installation And Configuration Manual Download

Page: 54 / 64

4-10

PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration

OL-3495-02

Chapter 4 Configuring the PA-5EFL Port Adapter

Checking the Configuration

Cisco 7100 Series Routers

Following is an example of the

show version

command from a Cisco 7120 series router.

Router# show version

Cisco Internetwork Operating System Software

IOS (tm) EGR Software (c7100-IS-M), Version 12.0(4)XE, EARLY DEPLOYMENT

RELEASE)

TAC:Home:SW:IOS:Specials for info

Compiled Thu 10-Jun-99 15:32 by linda

Image text-base:0x60008900, data-base:0x60D8E000

ROM:System Bootstrap, Version 12.0(19990720:023243)

[gautham-conn_4xe-PRE_ALPHE

BOOTFLASH:EGR Software (c7100-IS-M), Version 12.0(4)XE, EARLY DEPLOYMENT

RELEA)

Router uptime is 24 minutes

System restarted by power-on

System image file is "disk0:c7100-is-mz.120-4.XE"

cisco 7120-bad (EGR) processor with 61440K/69632K bytes of memory.

R527x CPU at 225Mhz, Implementation 40, Rev 10.0, 2048KB L2 Cache

Last reset from power-on

Bridging software.

X.25 software, Version 3.0.0.

4 Ethernet/IEEE 802.3 interfaces.

125K bytes of non-volatile configuration memory.

40960K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).

8192K bytes of Flash internal SIMM (Sector size 256K).

Configuration register is 0x2000

Cisco 7200 Series and Cisco uBR7200 Series Routers

Following is an example of the

show version

command from a Cisco 7200 series router.

Router# show version

Cisco Internetwork Operating System Software

IOS (tm) 7200 Software (C7200-J-M), Version 11.1(7)CA [biff 105]

Compiled Sun 04-Aug-96 06:00 by biff

Image text-base: 0x600088A0, data-base: 0x605A4000

ROM: System Bootstrap, Version 11.1(7)CA RELEASED SOFTWARE

Router uptime is 4 hours, 22 minutes

System restarted by reload

System image file is “c7200-j-mz”, booted via slot0

cisco 7206 (NPE150) processor with 12288K/4096K bytes of memory.

R4700 processor, Implementation 33, Revision 1.0 (Level 2 Cache)

Last reset from power-on

Bridging software.

X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.

Chassis Interface.

4 Ethernet/IEEE 802.3 interfaces.

2 FastEthernet/IEEE 802.3 interfaces.

4 Token Ring /IEEE802.5 interfaces.

Summary of Contents for PA-5EFL=

































































Search results

Summary of Contents for PA-5EFL=

Reviews:

Related manuals for PA-5EFL=

Brands by name

Popular brands

Cisco PA-5EFL=, Installation And Configuration Manual

Search results

Summary of Contents for PA-5EFL=

Reviews:

Related manuals for PA-5EFL=

Brands by name

Popular brands