manualshive.com logo in svg

Cisco PA-5EFL=, Installation And Configuration Manual

Share
Download
Cisco PA-5EFL= Installation And Configuration Manual Download Page 23

C H A P T E R

2-1

PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration

OL-3495-02

2

Preparing for Installation

This chapter describes the general equipment, safety, and site preparation requirements for installing the 
Cisco PA-5EFL port adapter. This chapter contains the following sections:

•

Required Tools and Equipment, page 2-1

•

Software and Hardware Requirements, page 2-2

•

Safety Guidelines, page 2-3

•

FCC Class A Compliance, page 2-8

Required Tools and Equipment

You need the following tools and parts to install a port adapter. If you need additional equipment, contact 
a service representative for ordering information.

•

PA-5EFL(=)

•

VIP2 (for installation in the Cisco 7000 series or Cisco 7500 series chassis only). For information 
about the specific VIP models that support the PA-5EFL port adapter, see the 

“Software and 

Hardware Requirements” section on page 2-2

.

•

Cables appropriate for the port adapter interfaces (ST-type optical-fiber cables are not available from 
Cisco Systems; they are available from outside commercial cable vendors.)

•

Number 1 Phillips and a 3/16-inch, flat-blade screwdriver (for VIP2 installation only).

•

Number 2 Phillips screwdriver.

•

Your own electrostatic discharge (ESD)-prevention equipment or the disposable grounding wrist 
strap included with all upgrade kits, field-replaceable units (FRUs), and spares.

•

Antistatic mat.

•

Antistatic container.

Summary of Contents for PA-5EFL=

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands