manualshive.com logo in svg

Cisco PA-5EFL=, Installation And Configuration Manual

Share
Download
Cisco PA-5EFL= Installation And Configuration Manual Download Page 20

 

1-8

PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration

OL-3495-02

Chapter 1      Overview

Identifying Interface Addresses

Identifying Interface Addresses

This section describes how to identify interface addresses for the PA-5EFL port adapter in supported 
platforms. Interface addresses specify the actual physical location of each interface on a router or switch.

Interfaces on the PA-5EFL installed in a router maintain the same address regardless of whether other 
port adapters are installed or removed. However, when you move a port adapter to a different slot, the 
first number in the interface address changes to reflect the new port adapter slot number.

Interfaces on a PA-5EFL installed in a VIP maintain the same address regardless of whether other 
interface processors are installed or removed. However, when you move a VIP to a different slot, the 
interface processor slot number changes to reflect the new interface processor slot.

Note

Interface ports are numbered from left to right starting with 0.

Table 1-5

 explains how to identify interface addresses.

Table 1-5

Identifying Interface Addresses

Platform

Interface Address Format

Numbers

Syntax

Cisco 7120 series routers

Port-adapter-slot-number/interface-port-number

Port adapter slot—always 3

Interface port—0 through 4

3/1

Cisco 7140 series routers

Port-adapter-slot-number/interface-port-number

Port adapter slot—always 4

Interface port—0 through 4

4/0

Cisco 7200 series routers

Port-adapter-slot-number/interface-port-number

Port adapter slot—0 through 
6 (depends on the number of 
slots in the router)

1

Interface port—0 through 4

1.

Port adapter slot 0 is reserved for the Fast Ethernet port on the I/O controller (if present).

1/0

Cisco uBR7246 router

Port-adapter-slot-number/interface-port-number

Port adapter slot—always 1 
or 2

1

Interface port—0 through 4

1/2

Cisco 7301 router

Port-adapter-slot-number/interface-port-number

Port adapter slot always—1

Interface port—0 through 4

1/0

VIP in Cisco 7000 series or
Cisco 7500 series routers

Interface-processor-slot-number/port-adapter-slot-n
umber/
interface-port-number

Interface processor slot—0 
through 12 (depends on the 
number of slots in the 
router)

Port adapter slot—always 0 
or 1

Interface port—0 through 4

3/1/0

Summary of Contents for PA-5EFL=

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands