Cisco PA-2FE-FX T Installation And Configuration Manual Download Page 75

Page: 75 / 78

4-17

PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration

OL-3474-06

Chapter 4 Configuring the PA-2FE

Checking the Configuration

Cisco 7200 Series Routers

The example of the

show interfaces fastethernet

command shows information specific to a Fast

Ethernet interface on a PA-2FE in slot 2:

Router#

show interfaces fastethernet 2/0

FastEthernet2/0 is up, line protocol is up

Hardware is i82543 (Livengood), address is 0030.1983.b438 (bia 0030.1983.b438)

MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

Keepalive set (10 sec)

Half-duplex, 100Mb/s, 100BaseTX/FX

ARP type:ARPA, ARP Timeout 04:00:00

Last input 00:00:06, output 00:00:09, output hang never

Last clearing of "show interface" counters 00:01:29

Queueing strategy:fifo

Output queue 0/40, 0 drops; input queue 0/75, 0 drops

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

2 packets input, 690 bytes

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

0 watchdog

0 input packets with dribble condition detected

14 packets output, 2220 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 babbles, 0 late collision, 0 deferred

1 lost carrier, 0 no carrier

0 output buffer failures, 0 output buffers swapped out

Note

For the Cisco 7206 router shelves, the

show interfaces

command requires a shelf number in the format

show interfaces

type shelf number/port adapter slot/port

Cisco 7401ASR Routers

The example of the

show interfaces fastethernet

command shows information specific to a Fast

Ethernet interface on a PA-2FE in slot 1:

Router#

show interfaces fastethernet 1/0

FastEthernet1/0 is up, line protocol is up

Hardware is i82543 (Livengood), address is 0030.1983.b438 (bia 0030.1983.b438)

MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

Keepalive set (10 sec)

Half-duplex, 100Mb/s, 100BaseTX/FX

ARP type:ARPA, ARP Timeout 04:00:00

Last input 00:00:06, output 00:00:09, output hang never

Last clearing of "show interface" counters 00:01:29

Queueing strategy:fifo

Output queue 0/40, 0 drops; input queue 0/75, 0 drops

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

2 packets input, 690 bytes

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

0 watchdog

0 input packets with dribble condition detected

14 packets output, 2220 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

Summary of Contents for PA-2FE-FX T















































































Search results

Summary of Contents for PA-2FE-FX T

Reviews:

Related manuals for PA-2FE-FX T

Brands by name

Popular brands

Cisco PA-2FE-FX T, Installation And Configuration Manual

Search results

Summary of Contents for PA-2FE-FX T

Reviews:

Related manuals for PA-2FE-FX T

Brands by name

Popular brands