Cisco PA-2FE-FX T Installation And Configuration Manual Download Page 22

Page: 22 / 78

1-6

PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration

OL-3474-06

Chapter 1 Overview

Network Management

Figure 1-7

Crossover Cable Pinout—PA-2FE-TX RJ-45 Connections Between Hubs and Repeaters

Figure 1-8

shows the duplex SC connector (one required for both transmit and receive), and

Figure 1-9

shows the simplex SC connector (two required, one each for transmit and receive) used for PA-2FE-FX
optical-fiber connections. Cisco does not supply these multimode optical-fiber cables; they are available
from a commercial supplier.

Figure 1-8

PA-2FE-FX Duplex SC Connector

Figure 1-9

PA-2FE-FX Simplex SC Connector

Network Management

The PA-2FE port adapters support the following:

•

SNMP agent v1 (RFC 1155–1157)

•

Ethernet MIB (RFC 1398)

•

IEEE 802.3 LAN specification for CSMA/CD

•

MIB for Network Management of TCP/IP-Based Internets: MIB-II (RFC 1213)

•

Definition of Managed Objects for Bridges (RFC 1493)

•

Evolution of Interfaces Group of MIB-II (RFC 1573)

Ethernet port

1 TxD+

2 TxD–

3 RxD+

6 RxD–

1 TxD+

2 TxD–

3 RxD+

6 RxD–

38583

DTE

H2214

H2399

Summary of Contents for PA-2FE-FX T















































































Search results

Summary of Contents for PA-2FE-FX T

Reviews:

Related manuals for PA-2FE-FX T

Brands by name

Popular brands

Cisco PA-2FE-FX T, Installation And Configuration Manual

Search results

Summary of Contents for PA-2FE-FX T

Reviews:

Related manuals for PA-2FE-FX T

Brands by name

Popular brands