Cisco ONS 15454 Hardware Installation Manual Download Page 461

Page: 461 / 516

Figure 283: Connecting the ONS 15454 M6 Multishelf Node and the ONS 15454 M6 Subtending Shelves in a Ring Topology

Stop. You have completed this procedure.

Air Deflector

An air deflector is a sheet-metal part that is mounted on the ONS 15454 M6 shelf to orient the air flow in a
specific direction.

Air deflectors can be mounted in different positions to control the air flow:

• Front to Front—Only ETSI rack
• Front to Back—For ANSI and ETSI racks
• Front to Top—Only ETSI rack

In an ANSI rack, the air deflectors are mounted only on the 23-inch rack configuration.

Cisco ONS 15454 Hardware Installation Guide

431

Installing the ONS 15454 M6 Shelf

Air Deflector

Summary of Contents for ONS 15454




































































































































































































































































































































































































































































































































Search results

Summary of Contents for ONS 15454

Reviews:

Cisco ONS 15454, Hardware Installation Manual, Page: 461 / 516

Search results

Summary of Contents for ONS 15454

Reviews: