Cisco MCS 7800 Series Administrator'S Manual Download Page 26 | Manualshive

Page: 26 / 234

background image

Usage Notes

Purpose

Network Protocol

To communicate with IP, network
devices must have an assigned IP
address, subnet, and gateway.

IP addresses, subnets, and gateways
identifications are automatically
assigned if you are using the Cisco
IP Phone with Dynamic Host
Configuration Protocol (DHCP). If
you are not using DHCP, you must
manually assign these properties to
each phone locally.

The Cisco IP Phones support IPv6
address. For more information, see
the documentation for your particular
Cisco Unified Communications
Manager release.

IP is a messaging protocol that addresses
and sends packets across the network.

Internet Protocol (IP)

The Cisco IP Phone supports LLDP
on the PC port.

LLDP is a standardized network
discovery protocol (similar to CDP) that
is supported on some Cisco and
third-party devices.

Link Layer Discovery
Protocol (LLDP)

The Cisco IP Phone supports
LLDP-MED on the SW port to
communicate information such as:

•

Voice VLAN configuration

•

Device discovery

•

Power management

•

Inventory management

For more information about
LLDP-MED support, see the

LLDP-MED and Cisco Discovery
Protocol

white paper at this URL:

http://www.cisco.com/en/US/tech/
tk652/tk701/technologies_white_
paper0900aecd804cd46d.shtml

LLDP-MED is an extension of the LLDP
standard developed for voice products.

Link Layer Discovery
Protocol-Media Endpoint
Devices (LLDP-MED)

Cisco IP Phones use the RTP
protocol to send and receive real-time
voice traffic from other phones and
gateways.

RTP is a standard protocol for
transporting real-time data, such as
interactive voice and video, over data
networks.

Real-Time Transport
Protocol (RTP)

RTCP is enabled by default.

RTCP works in conjunction with RTP to
provide QoS data (such as jitter, latency,
and round trip delay) on RTP streams.

Real-Time Control
Protocol (RTCP)

Cisco IP Phone 7800 Series Administration Guide for Cisco Unified Communications Manager

12

Supported Network Protocols

«
...
24
25
26
27
28
...
»

Summary of Contents for MCS 7800 Series











































































































































































































































Reviews:

No comments

Related manuals for MCS 7800 Series

UNIVERGE SL2100

Brand: NEC Pages: 196

UNIVERGE SL2100

Brand: NEC Pages: 174

ElectraElite IPK

Brand: NEC Pages: 151

Mobile Multimedia AM/FM/DVD Receiver VM9311

Brand: Jensen Pages: 90

Brand: GSK Pages: 32

Brand: TANDBERG Pages: 12

Brand: Roger Pages: 2

Brand: YATOUR Pages: 27

Brand: Stahl Pages: 24

Brand: Juna Pages: 5

Brand: Raven Pages: 10

Brand: Huawei Pages: 109

Brand: Huawei Pages: 37

Brand: Huawei Pages: 8

Brand: Huawei Pages: 3

Brand: AudioBahn Pages: 13

SoundStation IP 7000

Brand: NEC Pages: 40

Conference Max Plus

Brand: NEC Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands