Cisco Linksys WRT54GP2 Installation And Troubleshooting Manual Download Page 42

Page: 42 / 112

Wireless-G Broadband Router with 2 Phone Ports

Chapter 5: Configuring the Router

The Security Tab - Filter

Edit MAC Filter Setting

. Click the

Edit MAC Filter Setting

button. Select the range of MAC address entries in

the drop-down box. In each

mac

field, enter the MAC address you want to filter. Click the

Apply

button before

closing the window. To cancel changes, click the

Undo

button.

Block WAN Requests

Use these features to enhance your network’s security and filter multicasting.

Block Anonymous Internet Requests

. This keeps your network from being “pinged” or detected and

reinforces your network security by hiding your network ports, so it is more difficult for intruders to work their
way into your network. Select

Enabled

to block anonymous Internet requests, or

Disabled

to allow anonymous

Internet requests.

Filter Multicast

. Multicasting allows for multiple transmissions to specific recipients at the same time. If

multicasting is permitted, then the Router will allow IP multicast packets to be forwarded to the appropriate
computers. Select

Enabled

to filter multicasting, or

Disabled

to disable this feature.

Filter Internet NAT Redirection

. This feature uses port forwarding to block access to local servers from local

networked computers. Select

Enabled

to filter Internet NAT redirection, or

Disabled

to disable this feature.

Filter IDENT (Port 113)

. This feature keeps port 113 from being scanned by devices outside of your local

network. Select

Enabled

to filter port 113, or

Disabled

to disable this feature.

When you have finished making changes to this screen, click the

Save Settings

button to save the changes, or

click the

Cancel Changes

button to undo your changes. Help information is shown on the right-hand side of a

screen. For additional information, click

More

Figure 5-22: Filtered MAC Address

Summary of Contents for Linksys WRT54GP2

















































































































Search results

Summary of Contents for Linksys WRT54GP2

Reviews:

Related manuals for Linksys WRT54GP2

Brands by name

Popular brands

Cisco Linksys WRT54GP2, Installation And Troubleshooting Manual

Search results

Summary of Contents for Linksys WRT54GP2

Reviews:

Related manuals for Linksys WRT54GP2

Brands by name

Popular brands