Cisco Linksys WRT54GP2 Installation And Troubleshooting Manual Download Page 34

Page: 34 / 112

Wireless-G Broadband Router with 2 Phone Ports

Chapter 5: Configuring the Router

The Setup Tab - Advanced Routing

Enter Route Name

. Enter a name for the static route, using a maximum of 25 alphanumeric characters.

Destination LAN IP

. The Destination LAN IP Address is the address of the remote network or host to which

you want to assign a static route. Enter the IP address of the host for which you wish to create a static route.

Subnet Mask

. The Subnet Mask determines which portion of a Destination IP address is the network

portion, and which portion is the host portion.

Gateway

. This is the IP address of the gateway device that allows for contact between the Router and the

remote network or host.

Hop Count

. This determines the maximum number of steps between network nodes that data packets will

travel. A node is any device on the network, such as PCs, print servers, routers, etc.

Interface

. Select

Local

Internet

, depending on the location of the static route’s final destination.

Delete Entry

. If you need to delete a route, select its number from the drop-down menu, and click the

Delete

Entry

button.

Show Routing Table

. Click the

Show Routing Table

button to open a screen displaying how data is routed

through your local network. For each route, the Destination LAN IP address, Subnet Mask, Default Gateway, Hop
Count, and Interface are displayed. Click the

Refresh

button to update the information.

When you have finished making changes to this screen, click the

Save Settings

button to save the changes, or

click the

Cancel Changes

button to undo your changes. Help information is shown on the right-hand side of a

screen. For additional information, click

More

Figure 5-13: Routing Table Entry List

Summary of Contents for Linksys WRT54GP2

















































































































Search results

Summary of Contents for Linksys WRT54GP2

Reviews:

Related manuals for Linksys WRT54GP2

Brands by name

Popular brands

Cisco Linksys WRT54GP2, Installation And Troubleshooting Manual

Search results

Summary of Contents for Linksys WRT54GP2

Reviews:

Related manuals for Linksys WRT54GP2

Brands by name

Popular brands