Cisco Linksys WRT54GP2 Installation And Troubleshooting Manual Download Page 97

Page: 97 / 112

Wireless-G Broadband Router with 2 Phone Ports

Appendix E: Glossary

DSL

(

igital

ubscriber

ine) - An always-on broadband connection over traditional phone lines.

DSSS

(

irect-

equence

pread-

pectrum) - Frequency transmission with a redundant bit pattern resulting in a lower

probability of information being lost in transit.

DTIM

(

elivery

raffic

ndication

essage) - A message included in data packets that can increase wireless efficiency.

Dynamic IP Address

- A temporary IP address assigned by a DHCP server.

EAP

(

xtensible

uthentication

rotocol) - A general authentication protocol used to control network access. Many specific

authentication methods work within this framework.

EAP-PEAP

(

xtensible

uthentication

rotocol-

rotected

xtensible

uthentication

rotocol) - A mutual authentication

method that uses a combination of digital certificates and another system, such as passwords.

EAP-TLS

(

xtensible

uthentication

rotocol-

ransport

ayer

ecurity) - A mutual authentication method that uses digital

certificates.

Encryption

- Encoding data transmitted in a network.

Ethernet

- A networking protocol that specifies how data is placed on and retrieved from a common transmission medium.

Finger

- A program that tells you the name associated with an e-mail address.

Firewall

- A set of related programs located at a network gateway server that protects the resources of a network from users

from other networks.

Firmware

- The programming code that runs a networking device.

Fragmentation

-Breaking a packet into smaller units when transmitting over a network medium that cannot support the

original size of the packet.

FTP

(

ile

ransfer

rotocol) - A protocol used to transfer files over a TCP/IP network.

Summary of Contents for Linksys WRT54GP2

















































































































Search results

Summary of Contents for Linksys WRT54GP2

Reviews:

Related manuals for Linksys WRT54GP2

Brands by name

Popular brands

Cisco Linksys WRT54GP2, Installation And Troubleshooting Manual

Search results

Summary of Contents for Linksys WRT54GP2

Reviews:

Related manuals for Linksys WRT54GP2

Brands by name

Popular brands