Cisco Linksys WRT54GP2 Installation And Troubleshooting Manual Download Page 95

Page: 95 / 112

Wireless-G Broadband Router with 2 Phone Ports

Appendix E: Glossary

Appendix E: Glossary

802.11b

- A wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency

of 2.4GHz.

802.11g

- A wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of

2.4GHz, and backward compatibility with 802.11b devices.

Access Point

- A device that allows wireless-equipped computers and other devices to communicate with a wired network.

Also used to expand the range of a wireless network.

Adapter

- A device that adds network functionality to your PC.

Ad-hoc

- A group of wireless devices communicating directly with each other (peer-to-peer) without the use of an access

point.

AES

(

dvanced

ncryption

tandard) - A security method that uses symmetric 128-bit block data encryption.

Backbone

- The part of a network that connects most of the systems and networks together, and handles the most data.

Bandwidth

- The transmission capacity of a given device or network.

Beacon Interval

- Data transmitted on your wireless network that keeps the network synchronized.

Bit

- A binary digit.

Boot

- To start a device and cause it to start executing instructions.

Bridge

- A device that connects different networks.

Broadband

- An always-on, fast Internet connection.

Summary of Contents for Linksys WRT54GP2

















































































































Search results

Summary of Contents for Linksys WRT54GP2

Reviews:

Related manuals for Linksys WRT54GP2

Brands by name

Popular brands

Cisco Linksys WRT54GP2, Installation And Troubleshooting Manual

Search results

Summary of Contents for Linksys WRT54GP2

Reviews:

Related manuals for Linksys WRT54GP2

Brands by name

Popular brands