manualshive.com logo in svg

Cisco G1 - Network Processing Engine G1, Installation And Configuration Information

Share
Download
Cisco G1 - Network Processing Engine G1 Installation And Configuration Information Download Page 64

 

7-64

Network Processing Engine and Network Services Engine Installation and Configuration

OL-4448-12

Chapter 7      NPE-G1 and NPE-G2 Installation and Configuration Information

Upgrading ROMmon on the NPE-G1 or NPE-G2

Using the show rom-monitor Command and ROMmon CLI showmon Commands

Use the 

show rom-monitor 

command if you are in Cisco IOS, or the ROMmon CLI

 showmon

 command 

if you are in ROMmon, to determine which ROMmon images are available. See the following examples 
for information shown in the output of the 

show rom-monitor

 or ROMmon CLI 

showmon

 commands:

•

If you are in Cisco IOS, use the 

show rom-monitor

 command:

Router> 

show rom-monitor

ReadOnly ROMMON version:

System Bootstrap, Version 12.2(20031011:151758)

Copyright (c) 1994-2003 by cisco Systems, Inc.

Upgrade ROMMON version:

System Bootstrap, Version 12.2(20031011:151758)

Copyright (c) 1994-2003 by cisco Systems, Inc.

Currently running ROMMON from Upgrade region

ROMMON from Upgrade region is selected for next boot

•

If you are in ROMmon, use the

 

ROMmon CLI

 showmon

 command:

rommon 1 > 

showmon

ReadOnly ROMMON version is:

System Bootstrap, Version 12.2(20031011:151758) [biff]

Copyright (c) 1994-2003 by cisco Systems, Inc.

Upgrade ROMMON version is:

System Bootstrap, Version 12.2(20031011:151758) [biff]

Copyright (c) 1994-2003 by cisco Systems, Inc.

Upgrade ROMMON currently running

Upgrade ROMMON is selected for next boot

rommon 2 >

Using the upgrade rom-monitor file Command

Use the 

upgrade rom-monitor file 

file_id

 command to program the ROMmon.

See the following example of the 

upgrade rom-monitor file

 command: 

Router#

upgrade rom-monitor file 

tftp://00.0.00.0/biff/C7200_NPEG2_RMFUR.srec

Loading pgettner/C7200_NPEG2_RMFUR.srec from 00.0.00.0 (via GigabitEthernet0/1):

 !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

[OK - 392348 bytes]

This command will reload the router. Continue? [yes/no]:yes

ROMMON image upgrade in progress.

Erasing boot flash eeeeeeeeeeeeeeeeee

Programming boot flash ppppp

Now Reloading via hard watchdog timeout

Unexpected exception, CP

System Bootstrap, Version 12.2(20031011:151758) [biff]

Copyright (c) 1994-2003 by cisco Systems, Inc.

Summary of Contents for G1 - Network Processing Engine G1





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands