manualshive.com logo in svg

Cisco G1 - Network Processing Engine G1, Installation And Configuration Information

Share
Download
Cisco G1 - Network Processing Engine G1 Installation And Configuration Information Download Page 29

 

7-29

Network Processing Engine and Network Services Engine Installation and Configuration

OL-4448-12

Chapter 7      NPE-G1 and NPE-G2 Installation and Configuration Information

Installing the NPE-G1 or NPE-G2

Note

The NPE-G1 or NPE-G2 is not fully seated in the router midplane until you tighten its captive 
installation screws.

Step 4

If you removed power supplies from the router, replace the power supplies. (See the 

“Removing and 

Replacing an AC-Input or DC-Input Power Supply” section on page 10-14

 when replacing a power 

supply in a Cisco 7200 VXR router.)

Step 5

If you slid the front of the router out of the rack, slowly guide the router back into the rack.

Step 6

Use a 3/16-inch flat-blade screwdriver to tighten the screws that secure the router to the front mounting 
strips of the rack.

This completes the procedure for installing the NPE-G1 or NPE-G2 in a Cisco 7200 VXR router.

Attaching the Rear Cable-Management Brackets and Cables (Optional)

You may choose to use one of two types of cable-management brackets. One type is the same as is used 
on the front of the router for managing port adapter and I/O controller cables. The NPE-G1- or 
NPE-G2-specific bracket is used only on the NPE-G1 or NPE-G2, and provides more support for optical 
fiber cables. 

Depending on whether the router is front-mounted or rear-mounted in the rack, install the 
cable-management brackets to the router. Go to one of these sections for instructions on rear-mounting 
the cable-management brackets and attaching the cables:

•

Installing the NPE-G1 or NPE-G2 Cable-Management Brackets, page 7-29

—This procedure applies 

to both the Cisco 7200 VXR routers and Cisco uBR7200 series routers. 

•

Installing the Rear Cable-Management Brackets on a Front-Mounted Router (Optional), 
page 7-31

—This procedure applies to only the Cisco 7200 VXR routers. 

•

Installing the Rear Cable-Management Brackets on a Rear-Mounted Router (Optional), 
page 7-32

—This procedure applies to only the Cisco 7200 VXR routers. 

•

Installing the Default Cable-Management Bracket on a Cisco uBR7246VXR Router (Optional), 
page 7-34

—This procedure applies to only the Cisco UBR 7246VXR universal broadband router.

Installing the NPE-G1 or NPE-G2 Cable-Management Brackets

If you are using the NPE-G1 or NPE-G2 and installing the cable-management bracket (Cisco Product 
Number MAS-7200-CBLMGMT), use the following instructions. 

Figure 7-17

 illustrates installing the 

bracket on the NPE-G1 or NPE-G2 on the Cisco 7200 VXR routers. 

Figure 7-18

 illustrates installing the 

bracket on the Cisco uBR7200-NPE-G1 or Cisco uBR7200-NPE-G2 on the Cisco uBR7200 series 
routers. 

Note

The captive installation screws on the NPE-G1 or NPE-G2 must be fastened to allow the 
cable-management bracket to provide proper cable support and strain relief. Always ensure that the 
captive installation screws are properly tightened. 

Summary of Contents for G1 - Network Processing Engine G1





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands