manualshive.com logo in svg

Cisco G1 - Network Processing Engine G1, Installation And Configuration Information

Share
Download
Cisco G1 - Network Processing Engine G1 Installation And Configuration Information Download Page 50

 

7-50

Network Processing Engine and Network Services Engine Installation and Configuration

OL-4448-12

Chapter 7      NPE-G1 and NPE-G2 Installation and Configuration Information

Enabling the Second Processor on the NPE-G1

CPU% per hour (last 72 hours)

* = maximum CPU% # = average CPU% 

Using the show mpf interface Command

Using the 

show mpf interface

 command without arguments shows the interface information for all 

Gigabit Ethernet interfaces and subinterfaces. This command is supported only for physical interfaces. 
There is no support for the virtual access interface.

Router#

 show mpf interface 

Name 

Index State Counter 

Count 

Gi0/1 0  up 

RX 

packets 

1004 

RX bytes 

158632 

TX packets    5004 

TX bytes

790632 

RX punts 

 32961 

TX punts 

 85972 

Gi0/1 1  up 

Gi0/1.100 100 

up 

RX 

packets 

  1004 

RX bytes 

 158632 

TX packets   

5004 

TX bytes 

 790632 

RX punts 

 

25 

Gi0/1.101 101 

up 

Gi0/1.102 102 

up 

Gi0/1.105 105 

up 

Gi0/1.106 106

up 

Gi0/1.107 107 

up 

Gi0/1.200 200 

up 

Gi0/1.201  201 

up

RX punts  

29 

Gi0/1.202 202

up 

Gi0/1.206 206 

up 

Gi0/1.2002  602 

up 

RX punts 

 26114 

Gi0/1.2004 604

up

Using the show mpf interface GigabitEthernet 0/1 Command

The following example displays the interface information for GigabitEthernet 1/0, subinterface number 
100. However, all Gigabit Ethernet interface and subinterface information is displayed because MPF 
does not recognize the subinterface number, unless it is a VLAN number.

Router# 

show mpf interface GigabitEthernet 0/1.100

Name Index 

State 

Counter 

Count

Gi0/1 0 

up 

RX 

packets 

1004

                                RX bytes 

158632

                                TX packets 

5004

                                TX bytes 

790632

                                RX punts 

32996

                                TX punts 

86062

Gi0/1 1 

up

Gi0/1.100 100 up 

RX 

packets 

1004

                                RX bytes 

158632

                                TX packets 

5004

                                TX bytes 

790632

                                RX punts 

25

Gi0/1.101 101 up

Gi0/1.102 102 up

Gi0/1.105 105 up

Gi0/1.106 106 up

Gi0/1.107 107 up

Gi0/1.200 200 up

Summary of Contents for G1 - Network Processing Engine G1





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands