manualshive.com logo in svg

Cisco G1 - Network Processing Engine G1, Installation And Configuration Information

Share
Download
Cisco G1 - Network Processing Engine G1 Installation And Configuration Information Download Page 35

 

7-35

Network Processing Engine and Network Services Engine Installation and Configuration

OL-4448-12

Chapter 7      NPE-G1 and NPE-G2 Installation and Configuration Information

Installing the NPE-G1 or NPE-G2

Figure 7-23

Installing the Chassis in a Telco-Type Rack with an Installed Cable-Management 
Bracket

Reconnecting Input Power and Powering Up the Router

The following procedures explain how to reconnect input power to a Cisco 7200 VXR router, Cisco 
UBR7225VXR, or Cisco uBR7246VXR router, power up the router, and verify a successful system boot.

Warning

Read the installation instructions before you connect the system to its power source.

 Statement 10

Reconnecting AC-Input Power to the Cisco 7200 VXR Router

To reconnect AC-input power to a Cisco 7200 VXR router, complete the following steps:

Step 1

At the rear of the router, check that the power switch on the power supply is in the off (O) position.

Step 2

Slide the cable-retention clip up away from the AC receptacle, and plug in the power cable.

Step 3

Secure the cable in the power supply AC receptacle by sliding the cable-retention clip down until it snaps 
around the connector. The cable-retention clip provides strain relief for the AC power cable. 

1

Rack-mount bracket

2

Cable-management bracket

93812

1

2

Summary of Contents for G1 - Network Processing Engine G1





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands