Cisco CRS Configuration Manual Download Page 235 | Manualshive

Page: 235 / 430

background image

DETAILED STEPS

Purpose

Command or Action

Enters global configuration mode.

configure

Example:

RP/0/RP0/CPU0:router# configure

Step 1

Configures an MPLS-TE tunnel interface.

interface tunnel-te tunnel-id

Example:

RP/0/RP0/CPU0:router#

interface tunnel-te 1

Step 2

Assigns a destination address on the new tunnel.

destination ip-address

Step 3

Example:

RP/0/RP0/CPU0:router(config-if)#

destination

The destination address is the remote node

’

s MPLS-TE router

ID.

192.168.92.125

Assigns a source address so that forwarding can be performed
on the new tunnel. Loopback is commonly used as the interface
type.

ipv4 unnumbered type interface-path-id

Example:

RP/0/RP0/CPU0:router(config-if)#

ipv4

Step 4

unnumbered Loopback0

Sets the path option to dynamic and assigns the path ID.

path-option preference - priority dynamic

Example:

RP/0/RP0/CPU0:router(config-if)#

path-option

Step 5

l dynamic

Sets the CT0 bandwidth required on this interface. Because
the default tunnel priority is 7, tunnels use the default TE class
map (namely, class-type 1, priority 7).

signalled- bandwidth

{

bandwidth

[

class-type ct

] |

sub-pool bandwidth

}

Example:

RP/0/RP0/CPU0:router(config-if)#

Step 6

signalled-bandwidth 100

commit

—

Saves the configuration changes, and remains within

the configuration session.

Use the

commit

or

end

command.

Step 7

end

—

Prompts user to take one of these actions:

•

Yes

—

Saves configuration changes and exits the

configuration session.

•

No

—

Exits the configuration session without committing

the configuration changes.

Cisco IOS XR MPLS Configuration Guide for the Cisco CRS Router, Release 5.1.x

217

Implementing MPLS Traffic Engineering

Creating an MPLS-TE Tunnel

«
...
233
234
235
236
237
...
»

Summary of Contents for CRS















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CRS

CoreBuilder 9000

Brand: 3Com Pages: 12

CoreBuilder 9000

Brand: 3Com Pages: 8

Brand: Rosewill Pages: 8

Amana ACVM97 Series

Brand: Maytag Pages: 85

Brand: H&S Pages: 30

Brand: Chieftec Pages: 9

Brand: Blonder tongue Pages: 12

Brand: Raisecom Pages: 13

1RK-CHASSIS ONErack

Brand: Tvone Pages: 8

Brand: Travla Pages: 2

Brand: OSS Pages: 92

Brand: Allied Telesis Pages: 62

Brand: Supermicro Pages: 54

Brand: ASROCK Pages: 1

FortiGate FortiGate-5020

Brand: Fortinet Pages: 402

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands