Cisco Catalyst 9200 Series Hardware Installation Manual Download Page 15 | Manualshive

Page: 15 / 78

background image

Figure 6: Rear Panel of a C9200 Switch

Blue Beacon LED

4

RJ-45 console port

1

MGMT (RJ-45
10/100/1000 management
port)

5

Modular fan modules on
C9200 switches

2

StackWise-160 port
connector slots with stack
blanks installed

6

Power supply module
slots

3

RFID Tag

The switch has a built-in, front-facing, passive RFID tag that uses UHF RFID technology and requires an
RFID reader with compatible software. It provides auto-identification capabilities for asset management and
tracking. The RFID tags are compatible with the Generation 2 GS1 EPC Global Standard and are ISO 18000-6C
compliant. They operate in the 860- to 960-MHz UHF band. For more information, see

Radio Frequency

Identification (RFID) on Cisco Catalyst 9000 Family Switches White Paper

.

StackWise Ports

StackWise ports are used to connect switches in StackWise stacking configurations. The switch ships with a
0.5-meter StackWise cable that you can use to connect the StackWise ports. For more information on StackWise
cables, see

Connecting to the StackWise Ports, on page 29

Use only approved cables, and connect only to similar Cisco equipment. Equipment might be damaged if
connected to nonapproved Cisco cables or equipment.

Caution

Power Supply Modules

The switch has a field replaceable main AC power supply module and a redundant hot-swappable field
replaceable AC power supply module. The switch is powered through one or two internal power supply
modules. In switches with PoE capability, the redundant power supply can also be used for extra PoE power.

Cisco Catalyst 9200 Series Switches Hardware Installation Guide

9

Product Overview

RFID Tag

«
...
13
14
15
16
17
...
»

Summary of Contents for Catalyst 9200 Series















































































Reviews:

No comments

Related manuals for Catalyst 9200 Series

Brand: 3Com Pages: 2

CoreBuilder 5000

Brand: 3Com Pages: 16

CoreBuilder 9000

Brand: 3Com Pages: 24

Brand: Idem Pages: 2

Brand: IBM Pages: 2

Brand: Pathway connectivity solutions Pages: 2

Brand: Lantronix Pages: 2

Brand: FS Pages: 23

Brand: Waters Network Systems Pages: 16

TECMA Silence Marine

Brand: Thetford Marine Pages: 9

Brand: AdLuminis Pages: 8

Brand: N-Tron Pages: 169

Brand: LevelOne Pages: 35

Brand: S+S Pages: 16

8 PORT SMART SWITCH CE 232D4SS8

Brand: B&B Electronics Pages: 29

Smart view IC-1304-IO

Brand: C&C TECHNIC Pages: 2

Brand: SMC Networks Pages: 6

Brand: Lancom Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands