Cisco Catalyst 9200 Series Hardware Installation Manual Download Page 76

Page: 76 / 78

Figure 37: SFP+ Port LEDs

Network Module Link Status

Color

Link is off.

Off

Link is on; no activity.

Green

Activity on a link; no faults.

The LED will blink green even when there is very little control traffic.

Note

Blinking green

Link is off due to a fault or because it has exceeded a limit set in the switch software.

Link faults occur when non-compliant cabling is connected to an SFP/SFP+
port. Use only standard-compliant cabling to connect to Cisco SFP/SFP+ ports.
You must remove from the network any cable or device that causes a link fault.

Caution

Blinking amber

Link for the SFP/SFP+/SFP28/QSFP+ has been disabled.

Amber

Cisco Catalyst 9200 Series Switches Hardware Installation Guide

Switch LEDs

Summary of Contents for Catalyst 9200 Series














































































Search results

Summary of Contents for Catalyst 9200 Series

Reviews:

Related manuals for Catalyst 9200 Series

Brands by name

Popular brands

Cisco Catalyst 9200 Series, Hardware Installation Manual

Search results

Summary of Contents for Catalyst 9200 Series

Reviews:

Related manuals for Catalyst 9200 Series

Brands by name

Popular brands