Cisco Catalyst 9200 Series Hardware Installation Manual Download Page 14

Page: 14 / 78

Description

Network Module

This module has two 40G slots with a QSFP+ connector in each slot.

This module is supported only on C9200 Multigigabit Ethernet switches.

C9200-NM-2Q

Insert this blank module when the switch has no uplink ports to enable
sufficient airflow.

C9200-NM-BLANK

For information about installing a network module, see

Installing a Network Module, on page 34

Note

Rear Panel

The switch rear panel includes StackWise connectors, fan modules, and power supply modules.

Figure 5: Rear Panel of a C9200L Switch

Blue Beacon LED

RJ-45 console port

MGMT (RJ-45
10/100/1000 management
port)

Fixed fan modules on
C9200L switches

StackWise-80 port
connectors

Power supply module
slots

Cisco Catalyst 9200 Series Switches Hardware Installation Guide

Product Overview

Rear Panel

Summary of Contents for Catalyst 9200 Series














































































Search results

Summary of Contents for Catalyst 9200 Series

Reviews:

Related manuals for Catalyst 9200 Series

Brands by name

Popular brands

Cisco Catalyst 9200 Series, Hardware Installation Manual

Search results

Summary of Contents for Catalyst 9200 Series

Reviews:

Related manuals for Catalyst 9200 Series

Brands by name

Popular brands