Cisco Catalyst 3560-E Series Message Manual Download Page 21

Page: 21 / 150

2-3

Catalyst 3750-X, 3750-E, 3560-X, and 3560-E Switch System Message Guide

OL-9772-05

Chapter 2 Message and Recovery Procedures

ACLMGR Messages

•

SPANTREE Messages, page 2-99

•

SPANTREE_FAST Messages, page 2-106

•

SPANTREE_VLAN_SW Messages, page 2-107

•

STACKMGR Messages, page 2-107

(only Catalyst 3750-X and 3750-E switches)

•

STORM_CONTROL Messages, page 2-109

•

SUPERVISOR Messages, page 2-110

•

SUPQ Messages, page 2-110

•

SW_DAI Messages, page 2-112

•

SW_MACAUTH Messages, page 2-114

•

SW_MATM Messages, page 2-115

•

SW_VLAN Messages, page 2-115

•

SWITCH_QOS_TB Messages, page 2-121

•

TCAMMGR Messages, page 2-121

•

UDLD Messages, page 2-123

•

UFAST_MCAST_SW Messages, page 2-125

•

VQPCLIENT Messages, page 2-125

•

WCCP Messages, page 2-126

ACLMGR Messages

Error Message

ACLMGR-2-NOMAP: Cannot create ACL Manager data structures for VLAN Map

[chars].

Explanation

The ACL manager could not allocate the data structures needed to describe a VLAN

map into a form that can be loaded into hardware. This error is most likely caused by lack of free
memory. [chars] is the VLAN map name.

Recommended Action

Reduce other system activity to ease memory demands.

Error Message

ACLMGR-2-NOVLB: Cannot create memory block for VLAN [dec].

Explanation

The ACL manager could not save per-VLAN information needed for its correct

operation. Some per-interface features, such as access groups or VLAN maps, will not be configured
correctly. [dec] is the VLAN ID.

Recommended Action

Use a less complicated configuration that requires less memory.

Summary of Contents for Catalyst 3560-E Series























































































































































Search results

Summary of Contents for Catalyst 3560-E Series

Reviews:

Related manuals for Catalyst 3560-E Series

Brands by name

Popular brands

Cisco Catalyst 3560-E Series, Message Manual

Search results

Summary of Contents for Catalyst 3560-E Series

Reviews:

Related manuals for Catalyst 3560-E Series

Brands by name

Popular brands