Cisco C9124AXD Hardware Installation Manual Download Page 63

Page: 63 / 118

Wall Mounting the AP with Horizontal Kit

The mounting wall, attaching screws, and wall anchors must support the least 50-lb (22.7-kg) static weight.
The installer must supply proper screws and anchors in accordance with local codes.

Caution

Before you begin

Ensure that you have the following materials before beginning to mount the AP horizontally to a wall:

Table 9: Materials Needed for Mounting the AP using AIR-MNT-HORZ1= Kit

Supplied in the
Kit?

Materials Required

Yes

Wall/Pole Mount L-Bracket

Yes

Solar Shield Cover

Yes

(4) M6 x 12-mm Hex-head Bolts

Yes

(2) Adjustable Band Clamps 2 to 5 inch (51 to 127 mm) Dia

Yes

(4) 8-32 x 0.62” Phillips Pan Head Screw

(4) wall screws and anchors (specified for wall material)

Drill bit for wall anchors

10–mm box-end wrench or socket set

Phillips Screwdriver

Procedure

Step 1

Use the mounting bracket as a template to mark four screw hole locations on the mounting wall. See

Figure

63: Wall mount L-bracket screw hole dimensions, on page 56

for the mounting bracket screw hole locations

and dimensions. See

Figure 64: L-bracket AP mount dimensions, on page 56

for dimensions of the mounting

L-bracket.

Cisco Catalyst 9124AX Series Outdoor Access Point Hardware Installation Guide

Installation Overview

Wall Mounting the AP with Horizontal Kit

Summary of Contents for C9124AXD























































































































Search results

Summary of Contents for C9124AXD

Reviews:

Related manuals for C9124AXD

Brands by name

Popular brands

Cisco C9124AXD, Hardware Installation Manual

Search results

Summary of Contents for C9124AXD

Reviews:

Related manuals for C9124AXD

Brands by name

Popular brands