Cisco C9124AXD Hardware Installation Manual Download Page 87 | Manualshive

Page: 87 / 118

background image

Step 10

To seal the rubber gland to the fiber cable, hand tighten the gland nut. Using an adjustable wrench, tighten
the nut ¼ revolution to make a water-tight seal on the cable to approximately 15 to 22 lbf-in (17 to 25 kgf-cm)
torque.

When removing this SFP assembly, you must proceed in the reverse order of this installation. Start
by loosening the cable gland’s nut.

Caution

Powering the Access Point over Power-over-Ethernet

The AP can be powered through Power-over-Ethernet (PoE) using the following:

• 802.3at (PoE+): Any 802.3at (30W) compliant switch port or Cisco Power Injector AIR-PWRINJ6=

• 802.3bt: Any 802.3bt compliant switch port or IEEE 802.3bt compliant Power Injector

• Cisco Universal PoE (Cisco UPOE)

If 802.3af is used, both the 2.4-GHz and 5-GHz radios are disabled, and Ethernet gets downgraded to 1 GbE
speeds. The SFP port and PoE-OUT is also disabled.

Note

Cisco Catalyst 9124AX Series Outdoor Access Point Hardware Installation Guide

79

Installation Overview

Powering the Access Point over Power-over-Ethernet

«
...
85
86
87
88
89
...
»

Summary of Contents for C9124AXD























































































































Reviews:

No comments

Related manuals for C9124AXD

Brand: AirLive Pages: 2

Brand: UniFi Pages: 45

Brand: NETGEAR Pages: 2

Brand: AirLive Pages: 46

Brand: AMTC Pages: 81

Brand: Reliance Pages: 33

Brand: Ubiquiti Pages: 28

Brand: Ubiquiti Pages: 32

Brand: WAGO Pages: 66

Brand: Billion Pages: 2

BiPAC 74xx series

Brand: Billion Pages: 8

Brand: EnGenius Pages: 55

Brand: Cambium Networks Pages: 17

Brand: ELTEX Pages: 21

Brand: Ebyte Pages: 11

Brand: Ebyte Pages: 13

Brand: Ebyte Pages: 13

Brand: Ebyte Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands