Cisco C9124AXD Hardware Installation Manual Download Page 79

Page: 79 / 118

Figure 78: Terminating DC plug to the cable

Grommet and Seal Ring

DC 2-conductor 18 AWG cable

Gasket

Crimp Pins

Connector body

Seal Nut

Figure 79: Wire Stripping Length

cable

a) Dis-assemble the DC plug .
b) Pass the cable through the plug components.
c) Strip the cable end.

Remove the wire jacket and tin the wire strands. Tinning the strands helps to insert the wire
into the crimp pins.

Note

d) Insert wire conductor into crimp pins. Using a 0.10 inch (2.54 mm) Hex crimp tool, crimp the pin to the

wire to secure it in place. Repeat for the second pin. If you must re-do the crimping process, you can use
the 2 extra pins supplied.

e) Insert the crimped pins and wire into the female barrel of the connector body. Be sure to insert the proper

wire polarity into the corresponding barrel shown on the body. Push to be sure the pin is fully seated into
the barrel.

Pin 1 (+V) Pin 2 (-V), the connector body is marked (+) and (-) to show polarity pin assignments.

Note

Cisco Catalyst 9124AX Series Outdoor Access Point Hardware Installation Guide

Installation Overview

Connecting a DC Power Cable to the Access Point

Summary of Contents for C9124AXD























































































































Search results

Summary of Contents for C9124AXD

Reviews:

Related manuals for C9124AXD

Brands by name

Popular brands

Cisco C9124AXD, Hardware Installation Manual

Search results

Summary of Contents for C9124AXD

Reviews:

Related manuals for C9124AXD

Brands by name

Popular brands