background image

7

Cisco 819 Integrated Services Router Hardware Installation Guide

OL-23125-02

Preface

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you 
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar 
with standard practices for preventing accidents. Use the statement number provided at the end of 
each warning to locate its translation in the translated safety warnings that accompanied this 
device. 

Statement 1071

SAVE THESE INSTRUCTIONS

Waarschuwing

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan 
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij 
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard 
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de 
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt 
raadplegen.

BEWAAR DEZE INSTRUCTIES

Varoitus

TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin 
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu 
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen 
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien 
lausuntonumeroiden avulla.

SÄILYTÄ NÄMÄ OHJEET

Attention

IMPORTANTES INFORMATIONS DE SÉCURITÉ 

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant 
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez 
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures 
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des 
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, 
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

Warnung

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen 
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und 
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder 
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten 
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

Summary of Contents for 819 series





















































































Reviews: