Cincoze CS-100/P2000 Series User Manual Download

Page: 39 / 116

100/

P2000 Series | User Manual

1.6 System I/O

1.6.1 Front

DC IN

Used to plug a DC power input with terminal
block

DVI-D

Used to connect to a monitor with digital signal
interface

VGA

Used to connect to a monitor with analog signal
interface

LAN

Used to connect to local area network

Line-out

Used to connect to an external speaker

Mic-in

Used to connect to a microphone

USB 3.2 GEN1

Used to connect to USB 3.2 GEN1/2.0/1.1
compatible devices

USB 2.0

Used to connect to USB 2.0/1.1 compatible
devices

Digital I/O Terminal Block

The Digital I/O terminal block supports 16
isolated DIO (8 digital input and 8 digital output)

Fan Power Terminal Block

Used to connect to an external fan

SW: Remote Power On/Off Terminal Block

Used to connect to remote power on/off switch

COM

Used to connect to RS-232/422/485 serial
devices

Summary of Contents for CS-100/P2000 Series





















































































































Search results

Summary of Contents for CS-100/P2000 Series

Reviews:

Related manuals for CS-100/P2000 Series

Brands by name

Popular brands

Cincoze CS-100/P2000 Series, User Manual

Search results

Summary of Contents for CS-100/P2000 Series

Reviews:

Related manuals for CS-100/P2000 Series

Brands by name

Popular brands